VesselView Mobile

The VESSELVIEW MOBILE HAS BEEN DISCONTINUED.

Please see the Smartcraft Connect Mobile page for single engine boats.

For multiple engines, please see our SmartCraft Connect page.

VesselView Mobile - Connects Smartcraft enabled engines to your iOS or Android device via Bluetooth.

You can now have all of the digital data from your SmartCraft engine on your mobile device (iOS or Android) PLUS new features such as mapping, fault code diagnostic information, maintenance reminders, performance summary and more. Be in the know everywhere you go.

BENEFITS:

See all the SmartCraft engine parameters: fuel flow, water temperature, oil & water pressures, battery voltage, RPM, etc. (parameters available are specific to each engine family).
Get fault code diagnostic information so you know and understand if that fault is something to be addressed when you return back to the dock or it is something more significant.
Get mapping information for your body of water: Remember where that great restaurant was, fuel, etc. Record a memorable moment on the water, and more
Dealer Locator and Primary Dealer selector
Checklists associated with your boating lifestyle
Maintenance reminders and historical maintenance information logs
Web-based account to dive deeper into your connection with your boat – analyze fuel consumption trip to trip and year to year, relive those wonderful family trips or fantastic fishing moments
Compatible with most Mercury SmartCraft-capable engines built around 2003 (40 HP and up)
Use the Contact Us link with your engine serial number to check compatibility!

Engine fault codes on phone vesselview mobile engine parameters

Check to see if your engine is compatible with VesselView Mobile.

SUPPORTED MERCURY MARINE ENGINE CONFIGURATIONS ARE BELOW:

OUTBOARD Engine Compatibility
Model	Serial Range
30–40 HP (3 cyl) EFI 4 Stroke	0T409000 and above
40–60 HP (4 cyl) EFI 4 Stroke	All
75–115 HP EFI 4 Stroke	1B366823 and above
75–125 HP OptiMax	All
150 HP 4 Stroke	All
V6 OptiMax	0T178500 and above
V6 EFI 2 Stroke	0T409000 and above
Verado	All
*NOTE:* Some 2001 model year engines may require an ECM update.
MERCRUISER Engine Compatibility
Model	Serial Range
3.0L MPI	All
4.3L MPI	All
4.5L/6.2L - Mercury Built	All
5.0L/350 MAG/5.7L/377 MAG/6.2L MPI - GM	0M300000 and above
496/8.1L	All
8.2L	All
NOTE: 6.2L Black Scorpion SmartCraft compatible, 0M391777 and above.
MERCURY DIESEL Engine Compatibility
Model	Serial Range
2.0L/2.8L I4	All
3.0L V6 TDI	All
4.2L I6	All
4.2L V8 TDI	0M300000 and above
QSB/QSC/QSM11/QSL Series Cummins	All
MERCURY RACING Sterndrive Engine Compatibility
Model	Serial Range
520/525/540/565 EFI	All
600/662/700 SCi	All
850/1025/1075/1200 SCi	All
QC4v Models	All
MERCURY RACING OUTBOARD Engine Compatibility
Model	Serial Range
2.5 XS	All
200/225/250/300XS	All
225/300X Pro Max	All
350 Sci and 400R Verado	All

What Mercury engine configurations are supported? The VesselView Module will work in any of the following configurations:

• For single engine applications that do not have SmartCraft architecture (an available junction box at the helm), you can install the module directly on the engine. This setup does require the 10-pin termination resistor, typically yellow and installed on the engine harness.

• For multi-engine applications that do not have SmartCraft architecture (available junction box under the helm), see your Mercury Marine dealer for assistance with architecture configuration and installation.

• For boats WITH SmartCraft architecture in place, use an open port (remove weather cap) in a junction box or replace your junction box with a higher capacity unit if all ports are already used.

Android® is a registered trademark of Google®, Inc., Bluetooth® is a registered trademark of Bluetooth SIG, Inc., iOS® is a registered trademark of Cisco Systems®, Inc. (used under license by Apple ®, Inc.), SmartCraft® and VesselView® are registered trademarks of Brunswick® Corporation.