Search
Filters
Close

VesselView Mobile

VesselView Mobile - Connects Smartcraft enabled engines to your iOS or Android device via Bluetooth.  

 

 

You can now have all of the digital data from your SmartCraft engine on your mobile device (iOS or Android) PLUS new features such as mapping, fault code diagnostic information, maintenance reminders, performance summary and more. Be in the know everywhere you go. 

BENEFITS: 
  • See all the SmartCraft engine parameters: fuel flow, water temperature, oil & water pressures, battery voltage, RPM, etc. (parameters available are specific to each engine family). 
  • Get fault code diagnostic information so you know and understand if that fault is something to be addressed when you return back to the dock or it is something more significant.
  • Get mapping information for your body of water: Remember where that great restaurant was, fuel, etc. Record a memorable moment on the water, and more
  • Dealer Locator and Primary Dealer selector
  • Checklists associated with your boating lifestyle
  • Maintenance reminders and historical maintenance information logs
  • Web-based account to dive deeper into your connection with your boat – analyze fuel consumption trip to trip and year to year, relive those wonderful family trips or fantastic fishing moments
  • Compatible with most Mercury SmartCraft-capable engines built around 2003 (40 HP and up) 
  • Use the Contact Us link with your engine serial number to check compatibility!

BUY VESSELVIEW MOBILE KIT NOW

 

    Engine fault codes on phone   vesselview mobile engine parameters  vesselview mobile maintenance due

 

Check to see if your engine is compatible with VesselView Mobile. 

SUPPORTED MERCURY MARINE ENGINE CONFIGURATIONS ARE BELOW:

OUTBOARD Engine Compatibility
Model Serial Range
30–40 HP (3 cyl) EFI 4 Stroke 0T409000 and above
40–60 HP (4 cyl) EFI 4 Stroke All
75–115 HP EFI 4 Stroke 1B366823 and above
75–125 HP OptiMax All
150 HP 4 Stroke All
V6 OptiMax 0T178500 and above
V6 EFI 2 Stroke 0T409000 and above
Verado All
NOTE: Some 2001 model year engines may require an ECM update.
MERCRUISER Engine Compatibility
Model Serial Range
3.0L MPI All
4.3L MPI All
4.5L/6.2L - Mercury Built All
5.0L/350 MAG/5.7L/377 MAG/6.2L MPI - GM 0M300000 and above
496/8.1L All
8.2L All
NOTE: 6.2L Black Scorpion SmartCraft compatible, 0M391777 and above.
MERCURY DIESEL Engine Compatibility
Model Serial Range
2.0L/2.8L I4 All
3.0L V6 TDI All
4.2L I6 All
4.2L V8 TDI 0M300000 and above
QSB/QSC/QSM11/QSL Series Cummins All
MERCURY RACING Sterndrive Engine Compatibility
Model Serial Range
520/525/540/565 EFI All
600/662/700 SCi All
850/1025/1075/1200 SCi All
QC4v Models All
MERCURY RACING OUTBOARD Engine Compatibility
Model Serial Range
2.5 XS All
200/225/250/300XS All
225/300X Pro Max All
350 Sci and 400R Verado All

 

What Engine Configurations are Supported?  The VesselView Module will work in any of the following configurations:
 
• For single engine applications that do not have SmartCraft architecture (an available junction box at the helm), you can install the module directly on the engine. This setup does require the 10-pin termination resistor, typically yellow and installed on the engine harness. 

• For multi-engine applications that do not have SmartCraft architecture (available junction box under the helm), see your Mercury Marine dealer for assistance with architecture configuration and installation.

For boats WITH SmartCraft architecture in place, use an open port (remove weather cap) in a junction box or replace your junction box with a higher capacity unit if all ports are already used.
 

Android® is a registered trademark of Google®, Inc., Bluetooth® is a registered trademark of Bluetooth SIG, Inc., iOS® is a registered trademark of Cisco Systems®, Inc. (used under license by Apple ®, Inc.), SmartCraft® and VesselView® are registered trademarks of Brunswick® Corporation.

 


Sorry, not found

Mercury-Mercruiser 84-8M0157078 VesselView Mobile Kit 1-4 Engines

$248.06 $240.63